B&T APC9 at home

[u/TheGoldShipper]

Really wanted a APC9 or GHM9 but alas, prohib.

So I turned my 1970s 10/22 into the closest thing. 26inch OAL without comp.

Ruger 10/22 carbine receiver
SB22 Fixed Kit chassis
Ballistic Advantage 8” barrel
Tac Sol X Ring compensator
SBI super lite stock
TANDEMKROSS bolt release and skeletonized mag release
Butler Creek 25/22 mag pinned at 10 of course
Holosun ARO
Magpul VFG

[u/Sad-Stop-2401]

How is this not prohibited?

https://rcmp.ca/en/firearms/classes-firearms/classes-firearms-canada#s5

Firearms adapted from a rifle or shotgun, whether by sawing, cutting or any other alteration, and that, as so adapted are:

• less than 660 mm in length
  

- 660 mm or greater in length and has a barrel less than 457 mm in length

You changed barrel length to under 457 mm?

Butler Creek 25/22 mag pinned at 10 of course

Because same mag is designed for a handgun too? Otherwise it should be unlimited right?

PS : Intent of this comment is not to blame any person but to understand legal compliance here. If someone knows more on this topic, most humbly, I will like to be corrected. I am not a lawyer nor a firearm verifier. This is not a legal advice.

[u/skelectrician → u/Sad-Stop-2401]

There's no minimum barrel length for rimfires, just a minimum overall length of 660mm (26")

[u/Sad-Stop-2401 → u/skelectrician]

This is incorrect, please read the defn of prohibited firearm at :

https://rcmp.ca/en/firearms/classes-firearms/classes-firearms-canada#s5

It applies to all firearms including rimfire.

PS : Not a lawyer, not a legal advice.

[u/hunterofsteelhead → u/Sad-Stop-2401]

You keep saying youre not an expert and asking people to correct you and then when they correct you then you default to posting the same thing over and over. BTW I havent downvoted you im just confused whether you actually know what youre talking about or just repeating rcmp nonsense over everybody that may actually be correct

[u/Sad-Stop-2401 → u/hunterofsteelhead]

Not one of them have quoted an authoritative source or have admitted to be a lawyer or someone who knows this law well. To top it all some of them have made some obvious mistakes.

Again, it is not about me being right as much as it is to have an authoritative answer to this. The reason is because this is something that can land a person in trouble. I will like them to be able to find the right source for this question.

My position comes from the obvious literal reading of the law. If that is not correct, I will love to have an authoritative source for that.

BTW, it is not RCMP bullshit. It is actually the law. That is literal text of Firearms Act.

https://laws-lois.justice.gc.ca/eng/acts/C-46/page-14.html#h-117002

[u/TheGoldShipper → u/Sad-Stop-2401]

I’m going off the basis that a factory 10/22 8” barrel swap is not an alteration, it’s a part replacement. Then, since it’s not prohibited, it also isn’t restricted, because it’s rimfire. To be restricted It (ii) has a barrel less than 470 mm in length, and iii) is capable of discharging centre-fire ammunition in a semi-automatic manner. So since it meets the OAL requirement it would be non-restricted.

[u/Sad-Stop-2401 → u/TheGoldShipper]

If I were you, I would take a second opinion from a lawyer or a verifier. If you are covered by firearm insurance (this subreddit recommends that you should), you might get a consult that is covered. Do not take my words, talk to those professionals who understand this professionally and are legally bound to serve your interest.